EASY DIGI™ Sound Card Interface PSK RTTY SSTV NBEMS JT-65 VOX UNIT W/CABLES

Description

EASY DIGI™ Sound Card Interface PSK RTTY SSTV NBEMS JT-65 VOX UNIT W/CABLES
The KF5INZ EASY DIGI™ VOX UNIT
AN IMPORTANT WORD ABOUT NEWER LAPTOPS AND SOME DESKTOPS:
If your Laptop or desktop only has an "Earphone" jack, but no "Mic" jack, read your manual! It probably has the combined Earphone/Mic jack.
This is a 4 conductor jack wired as follows: TIP, RING, RING, SHIELD: Tip = right channel audio out. 1st Ring = left channel out. 2nd ring = ground. Shield = microphone input.
When you order I need to know whether or not your device is as above or uses the legacy separate mic and earphone jacks. If you do not give me that information then I can not guarantee that what I ship you will work on your pc and if post shipping modifications are required you will be responsible for shipping costs both ways as well as a modification fee.
I also need to know the make and model of the radio you wish to use the interface with and whether you wish to use the microphone/speaker jacks or a data or accessory jack.
There is a link button on every listing that says "Contact Seller". Please use that to send me your information. Thanks!
WORKS WITH FT8
No, we didn’t re-invent the wheel, we just made a convenient, single board, isolated, digital interface that works for almost all of the digital modes on HF and VHF/UHF.
Works with DIGIPAN, FLDIGI, MTTY, MMSSTV and most all other sound card programs! Work PSK-31, PSK-63, RTTY, SSTV, NBEMS, MT-63, plus many other
modes on your HF or VHF/UHF rig.
This unit works through your rigs VOX circuit to provide the xmit function. No USB or RS-232 hookups required, just activate your VOX, set your audio levels and go.
Please note, Microphone cable style and connector type will vary according to your specific radio.
This unit includes a cable with microphone connector and 3 three foot audio cables
Please send me a message indicating what make and model radio you want the Mic cable for! If you do not send that message your item will be delayed.
THIS IS THE EASIEST LEAST EXPENSIVE WAY I KNOW OF TO GET ON DIGITAL COMMUNICATIONS.
COMPARE TO THE COST OF A RIGBLASTER™ OR TNC.
HOOK UP TIME IS ABOUT 1 MINUTE AND YOU ARE ON THE AIR.
NO JUMPER HEADERS TO FIGURE OUT, JUST PLUG AND PLAY!
Nothing new about this technology, it consists of two 600 ohm line transformers for audio input and output from your pc to your transceiver.
Transformer coupled audio eliminates ground loops and AC hum on your signal
·
Very small size, only 3 13/16”L
x 1 9/16”W
x 3/4” H, can be mounted using the built in mounting tabs in just about any convenient location.
·
Case made of durable ABS Plastic for long life.
·
Weighs less than 3 ounces
·
High quality FR-4 double sided, solder masked, silk screened Printed Circuit Board
·
Compatible with most modern ham radio transceivers.
These interfaces have been tested on Kenwood TS-120, TS-530, TS-570, TS-930, TS-50, TM-261A, TM-G707A, ICOM IC2100H and
many other
radios.
Simply hook up per the enclosed wiring diagram, load your software, turn on the radio and have fun on your favorite digital mode!
Fully wired and assembled version in a mountable ABS plastic case.
Note: Requires 3 each 1/8” audio cables to connect from pc to interface and from radio to interface, and 1 1/8" audio plug to microphone connector cable to match your radio.